![]() Some keys from the keyboard that were not functioning after the spill. Another service center had quoted $900 the cost of replacing the mother board.Īt first the MBP "mostly" worked fine apart from the HDD which was clicking (due to a drop that happened before the water damage). Works than stops working / corrosion: a client brought a MPB drenched with water, for us to have a look. 1 year now and no complaints from this now happy return customer. Before breaking it apart, I sprayed some WD40 a few times, let it soak then drain out over the course of a couple of hours, and it worked since. It was sandwiched between two layers of glued/fused thin plastic and couldn't be removed without breaking the plastic layers. An unusual fix? I had a Vaio trackpad with coffee spilled in it, that wouldn't work. Completely dead is usually easier to fix than part dead, speaking from the experience I've had. connectors and sockets for those connectors. the whole trackpad), it can be useful to look at the gate e.g. If a whole "unit" is not working instead of parts of that unit (example: some key vs. If it's working at first, and starts "working less," then stops working, it usually is due to corrosion. Some means that seem extreme can be used when nothing else works and you have nothing to loose. Don't generalize, due to the so many places liquids can seep into and the extensive list of reactions, shorts, and damage they can cause. In addition to all what was written above, I would add: I had some experience with liquid spills: water, wine, screen cleaner, etc. If data on your computer is important, you can remove the Hard Drive and read its information by connecting it to another computer, even if yours does not work any more. ![]() ![]() If you are thinking that this is all an exaggeration consider that you could have anti static shoes, anti static pants, ant static shirt and anti static gloves, also the floor you step on could be anti static. You can get a ground connection from your wall sockets IF your sockets are PROPERLY grounded. If you want to be really safe you would need to buy an anti static wrist strap so that you are connected to ground ALL the time you are working with your computer. Like your computer's chassy (if its metallic) while STILL connected with a properly grounded power cable (you must touch where there is NO paint, usually the back of a desktop would be unpainted). Or house heating is used, especially electric heating.Īt the very least you must discharge yourself by touching an electrical ground. When disassembling, it is extremely important to use antistatic precautions, specially if you live in a place where air is dry. Do not do this in a hurry, this requires a lot of patience. Use DIELECTRIC spray, it is specially designed to clean electronic components without damaging the PCB (Printed Circuit Board) or electronic components, you can use a tooth brush if you are extremely careful. You need a microscope to actually be able to see this.īest possible solution is to disassemble the computer as suggested on other answers. Improper heating of solder will result in porous solder with increased electrical resistance, also known as "cold" solder. Hair driers can actually melt solder, depending on solder's composition. I am an electronics engineer, so trust me when I say With many laptop designs there's ''nothing between the bottom of the keyboard and the RAM, FAN, Optical Drive, and all the other parts of the logic board but AIR There's been a lot of well I spilled on laptop my keyboard, but itstill worked at first., If you're lucky enough not to kill it straight off, then at least remove, clean and dry the keyboard best as possible before continued use. Spraying with a DIELECTRIC electronic contact cleaner, and/or 99% alcohol will also speed the drying process (70% alcohol contains too much water).įorced air on the open parts is OK, but if you're in a humid environment packing up with desiccant in a trash bag or rubbermaid container and making changes over three days or so would be better. You really ought to open and dismantle the device as much as possible so that you can clean up, rinse off any residue that's right if it's already wet you can wash it and clean it so that there will be no corrosion occurring later. In my opinion 72hrs is a conservative wait time for drying- hours or a day mean nothing Best way to dry it is to seal it with a desiccant like silica packs (though even something like pasta can work in a pinch) or in a room with a dehumidifier. ![]() No hair dyers or any forced air on/into a closed device! you'll only be spreading any liquid not drained around inside where you can't see or get at it. Pull the power cord and remove the battery if possible.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |